THL 10-2413WI

DC/DC Converters THL 10WI Series, 10 Watt Features • 10 Watt in 1” x 1” package • Shielded metal case with isolated ing nd e p CB Scheme 226037 UL 60950-1 UL 60950-1 baseplate • Ultrawide 4:1 input voltage ranges • Remote On/Off control • Operating temp. range –40°C to +75°C and up to +85°C with heat-sink • I/O isolation voltage 1500 VDC • Input filter meets EN 55022 class A without external components • Cost optimized design • Industry standard pinout • 3-year product warranty The THL 10WI is a series of general purpose 10 Watt dc/dc-converters packed in the compact 1” x 1” case and is a pin to pin replacement for the popular 1” x 2” size products. The industrial standard pinout, the ultra wide 4:1 input voltage range and the input filter that meets EN 55022 Class A without external components make these converters easy to design in and suitable for to cost optimize many existing and new applications. The models have a remote On/Off control, short circuit and overvoltage protection and are applicable in temperature ranges of up to +75°C or +85°C with optional mounted heat sink. Typical applications are instrumentation, distributed power architectures in communication and industrial electronics. Models Order code Input voltage range Output voltage Output current max. Efficiency typ. THL 10-2410WI 3.3 VDC 2200 mA 86 % THL 10-2411WI 5.1 VDC 2000 mA 84 % 12 VDC 830 mA 86 % THL 10-2413WI 9 – 36 VDC 15 VDC 660 mA 87 % THL 10-2415WI (24 VDC nominal) 24 VDC 410 mA 86 % THL 10-2421WI ±5.0 VDC ±1000 mA 84 % THL 10-2422WI ±12 VDC ±410 mA 86 % THL 10-2423WI ±15 VDC ±330 mA 87 % THL 10-4810WI 3.3 VDC 2200 mA 85 % THL 10-4811WI 5.1 VDC 2000 mA 84 % THL 10-4812WI 12 VDC 830 mA 86 % THL 10-2412WI THL 10-4813WI 18 – 75 VDC 15 VDC 660 mA 87 % THL 10-4815WI (48 VDC nominal) 24 VDC 410 mA 86 % THL 10-4821WI ±5.0 VDC ±1000 mA 84 % THL 10-4822WI ±12 VDC ±410 mA 86 % THL 10-4823WI ±15 VDC ±330 mA 87 % http://www.tracopower.com Page 1 of 4 DC/DC Converters THL 10WI Series 10 Watt Input Specifications Input current at no load (at nominal input voltage) 24 V models: 30 mA typ. 48 V models: 20 mA typ. Input current at full load (at nominal input voltage) 24 V; 3.3 VDC 24 V; other 48 V; 3.3 VDC 48 V; other models: models: models: models: Start-up voltage / under voltage lockout 24 V models: (hysteresis for assertive on) 48 V models: Surge voltage (1 sec. max.) 400 mA typ. 500 mA typ.. 200 mA typ. 250 mA typ. 9 VDC / 8.5 VDC (or lower) 18 VDC / 17 VDC (or lower) (long term operation at undervoltage will demage the converter!) 24 Vin models: 50 V max. 48 Vin models: 100 V max. Conducted noise (input) EN 55022 class A, FCC part 15, level A without external components Recommended input fuse (slow blow) 24 V models: 2000 mA 48 V models: 1000 mA Output Specifications Voltage set accuracy ±2 % Regulation – Input variation (Vmin – Vmax) – Load variation 1.0 % max. single output models: 1.2 % max. (15 – 100 % load) dual output models: 2.0 % max. (15 – 100 % balanced load) Minimum load 15 % Ripple and noise (20 MHz bandwidth) 60 mVp-p typ. Temperature coefficient ±0.02 %/K Output current limitation >110 % of Iout max. Short circuit protection indefinite, automatic recovery Transient response setting time 300 µs typ. (25 % load step change) Maximum capacitive load http://www.tracopower.com 3.3 5 12 15 24 ±5.0 ±12 ±15 VDC VDC VDC VDC VDC VDC VDC VDC models: models: models: models: models: models: models: models: 560 µF 560 µF 150 µF 150 µF 68 µF 220 µF (each output) 100 µF (each output) 100 µF (each output) Page 2 of 4 DC/DC Converters THL 10WI Series 10 Watt General Specifications Temperature ranges – – – – Operating without heat sink –40°C to +75°C (with derating) Operating with heat sink –40°C to +85°C (with derating) Case temperature +100°C max. Storage –40°C to +125°C Power derating – Operating without heat sink 2.5 %/K above +60°C – Operating with heat sink 3.5 %/K above +70°C Thermal inpedance – Natural convection 18.2 K/W – Natural convection with heat sink 15.8 K/W Humidity (non condensing) 95 % rel H max. Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign) >350’000 h Isolation voltage (60 s) – Input/Output 1’500 VDC Isolation capacitance – Input/Output 1200 pF max. Isolation resistance – Input/Output (500 VDC) >1’000 MOhm Remote On/Off – On: 2.5 ... 50 VDC or open circuit – Off: 0 ... +1.0 VDC or short circuit pin 6 and pin 2 – Off idle current: 10 mA max. Switching frequency (fixed) 400 kHz typ. (pulse width modulation PWM) Altitude during operation 5‘000 m max. (16‘400 ft) approved Safety standards UL/cUL 60950-1, IEC/EN 60950-1 Safety approvals UL/cUL (File no. e188913, entry pending) CB 60950-1:2005 (2nd Ed.)+ A1:2009 + A2:2013 CSA 60950-1 – Certification documents www.tracopower.com/overview/thl10wi Environmental compliance – Reach www.tracopower.com/products/reach-declaration.pdf – RoHS RoHS directive 2011/65/EU Physical Specifications Casing material metal Baseplate non conductive FR4 Potting material epoxy (UL 94V-0 rated) Weight 15 g (0.53oz) Soldering temperature max. +260°C / 10 s Application note : www.tracopower.com/overview/thl10wi All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 3 of 4 DC/DC Converters THL 10WI Series 10 Watt Outline Dimensions 7.62 5.08 (0.3) (0.2) 1 2.5 5 (0.1) Bottom view (1.0) 2 25.4 (0.8) 20.32 6 Pin-Out 3 4 6.0 10.2 2.5 10.16 10.16 (0.24) (0.4) (0.1) (0.4) (0.4) Pin Single Dual 1 +Vin (Vcc) +Vin (Vcc) 2 –Vin (GND) –Vin (GND) 3 + Vout + Vout 4 No pin Common 5 –Vout –Vout 6 Remote On/Off 25.4 (1.0) Dimensions in [mm], () = Inch Pin diameter ø 1.0 (0.04) Pin pitch tolerances: ±0.25 (±0.01) Tolerances: ±0.5 (±0.02) Heat-Sink (Option) Order code: THL-HS1 (cont.: heat-sink, thermal pad, 2 clamps) Material: Aluminum Finish: Anodic treatment (black) Weight: 4.0 g (0.14oz) without converter Thermal impedance after assembling: 15.8 K/W 31.0 (1.22) max. Note: The product label on converter has to be removed before mounting the heat-sink. For volume orders converters will be supplied with heat-sink already mounted. Please contact factory for quotation. Separate heat-sinks are only available for prototypes and small quantity orders. Heat-sink Thermal pad Clamp Converter 16.3 (0.64) 17.5 (0.69) max. Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com Rev. November 18, 2021 www.tracopower.com Page 4 of 4